Torque

Forums

Forums

GaryDoug
@garydoug
Trusted Member
Joined: Jul 21, 2012
Topics: 3 / Replies: 69
Reply
RE: ELM327 cannot fin my car ECU

More than likely you got one of the ELM327 adapters that are "missing" the parts for the non-CAN (2007 and earlier) protocols. The CAN protocol was re...

12 years ago
Reply
RE: "I see conditions" but won't tell me what

I am not familiar with OBD2 on diesel vehicles. But on gasoline cars, it is possible for a temperature sensor to be in significant error and still not...

12 years ago
Reply
RE: Anyone with a 03+ crown Vic/grand marquis?

I can't say for sure of course, but that reading indicates a lot of vacuum ( -10psi relative ) and that would not be consistent with a vacuum leak.

12 years ago
Reply
RE: Anyone with a 03+ crown Vic/grand marquis?

It is probably unlikely to get someone with that particular car to respond. In light of that, here are some guidelines: The MAP (manifold absolute pre...

12 years ago
Reply
RE: "I see conditions" but won't tell me what

What it's saying is: "Caution ICY conditions" because either the engine coolant temperature sensor or the intake air temperature sensor is reporting t...

12 years ago
Reply
RE: e39 525d 2002 no connection

I mean what pins does the connector HAVE, not USE? Take a look at the connector and see what pins are installed. Few, if any, manufacturers install pi...

12 years ago
Reply
RE: Not communicating with ECU

Quote from cintakc on August 14, 2014 here shown as switch terminals 3.11 on 6.14 Good find!

12 years ago
Reply
RE: e39 525d 2002 no connection

What pins does the car's connector have? It looks like the only protocol for pre-2005 cars would be the K-line. I have noticed that some of the newer ...

12 years ago
Reply
RE: Not communicating with ECU

You are out of luck there. Pins 3 and 11 are not defined in the OBD2 standard. If there is a protocol for that car, it isn't a standard one. Any OBD2 ...

12 years ago
Reply
RE: Not communicating with ECU

What protocol does the X-bow use? What is the model of the ELM327 adapter? When and where did you get it? Most of the recent production does not have ...

12 years ago
Reply
RE: Trouble with OBD to ECM Communication

Resistors, caps, diodes, transistors, regulator IC These two boards are almost identical but the one on the left works for all protocols and the one ...

12 years ago
Reply
RE: Clone adapters - Currently many that dont' work on CANBUS

Here is one that might work. Notice the claim: "THE BAFX PRODUCTS SCAN TOOL WILL WORK ON ALL 1996 AND NEWER VEHICLES THAT ARE LOCATED IN THE USA! UNL...

12 years ago
Reply
RE: Clone adapters - Currently many that dont' work on CANBUS

Here is where I ordered mine. The ones I got would never work on your 02 S10. I have no idea where you can get one that works for your vehicle except ...

12 years ago
Topic
Reply
RE: Trouble with OBD to ECM Communication

I just bought 4 adapters on Amazon, all different and all were missing the parts for J1850 GM cars 96-2007. That's why one of your cars worked and ano...

12 years ago
Reply
RE: READ ME: Connected to Bluetooth but not to ECU

I recently bought 4 different devices on Amazon and they were all missing the parts for the J1850 and K-line. They were all different and all from dif...

12 years ago
Reply
RE: Clone adapters - Currently many that dont' work on CANBUS

I recently ordered four different clone OBD2/ELM327 bluetooth adapters on Amazon from four different sellers. NONE of them worked on my 98 Firebird. I...

12 years ago
Topic
14 years ago
Replies: 2
Views: 1081
Reply
RE: Bitwise PID math

I wasn't aware there was an operator like that. I have been using the "&" operator which should work for any value. i.e.(A&9)

14 years ago
Reply
RE: Software

Torque is for Android devices. Unless you know of an Android-based laptop, I suspect the answer is no. There are plenty of apps for Windows PC availab...

14 years ago
Page 3 / 4

  Follow me on twitter