Torque

Forums

Forums

Guest  

Show or hide header
Welcome Guest, posting in this forum require registration.

Torque » Torque OBD ECU Scanner » Torque Discussion / Ideas » Comprehensive list of PID operators and functions

Pages: 1 2 3 4 [5] 6
Author Topic: Comprehensive list of PID operators and functions
Capp777
Member
Posts: 2994
Post Re: Comprehensive list of PID operators and functions
on: April 16, 2018 (GMT)

I tested the following for STFT in my son’s
crown vic at idle…

(((A*256)+B)*(100/32768)-100)*-1.0

(A*(100/128)-100)*-1.0

which seemed to match OBD STFT min/max for both
banks. Would be curious if it works for you under
driving conditions.
vl_vic
Member
Posts: 11
Post Re: Comprehensive list of PID operators and functions
on: April 18, 2018 (GMT)

((A*256)+B)*(100/32768)-100)*-1.0 -this is the same formula as (((A*256)+B)-32768)/-327.68
at the data A=87 B=AE is obtained -6.00 but should be -5.4
the value is overstated.
cintakc
Member
Posts: 1663
Post Re: Comprehensive list of PID operators and functions
on: April 18, 2018 (GMT)

I looked at the answers for PID 221158 based on the program FORScan there is no linear dependence
vl_vic
Member
Posts: 11
Post Re: Comprehensive list of PID operators and functions
on: April 18, 2018 (GMT)

I also look at the answers in Forscan.
Capp777
Member
Posts: 2994
Post Re: Comprehensive list of PID operators and functions
on: April 18, 2018 (GMT)

The single byte A equation does yield -5.4 and
more likely mimics how OBD STFT is calculated.
The second byte B equation adds greater
resolution so the -6.0 seemed reasonable to
me.

https://torque-bhp.com/forums/?wpforumaction=viewtopic&t=635.0

vl_vic
Member
Posts: 11
Post Re: Comprehensive list of PID operators and functions
on: April 18, 2018 (GMT)

A=A0
B=00
Rezult -20.00
How to explain it?
Capp777
Member
Posts: 2994
Post Re: Comprehensive list of PID operators and functions
on: April 18, 2018 (GMT)

Not sure because with both equations
and A0 00 results are -25.0 by calculator.
vl_vic
Member
Posts: 11
Post Re: Comprehensive list of PID operators and functions
on: April 18, 2018 (GMT)

A=80
B=00
rezult=0.00
Ioniq-BEV
Member
Posts: 1
Post Re: Comprehensive list of PID operators and functions
on: April 21, 2018 (GMT)

..”Also, suggest having a MIN() and MAX() that returns a running minimum or maximum of a particular PID.”

How I can read running MIN and MAX value of any PID?
Functions MIN(A:B) and MAX(A:B) compares two numbers
FntX
Member
Posts: 64
Post Re: Comprehensive list of PID operators and functions
on: May 3, 2018 (GMT)

Quote from vl_vic on April 18, 2018
A=80
B=00
rezult=0.00

INT16(A:B)=8000[WORD]
8000 = DEC32768 – 32768 = 0
0/-327,68 = 0

Just have a look at the equation steps when using the test PID window.

Something seems odd to me. Where do you take these values from exactly? I do understand subtraction of 32768 but what about the division by -327,68 which is equal to (32768 * -10)?
vl_vic
Member
Posts: 11
Post Re: Comprehensive list of PID operators and functions
on: May 3, 2018 (GMT)

(((A * 256) + B) -32768) / – 327,68 -this is only an assumption. I do not know the real formula
Space
Member
Posts: 2
Post Re: Comprehensive list of PID operators and functions
on: July 2, 2018 (GMT)

This is my firs post and I need help. :)

I will need PID settings for AUDI TT OIL TEMP for engine and DSG gearbox.

Can some1 help?
artca
Member
Posts: 1
Post Re: Comprehensive list of PID operators and functions
on: August 13, 2018 (GMT)

I ham using a Samsung Galaxy tablet- the screen keyboard doesn’t seem to register decimal points. Is there a way around this- i.e., when the application asks for capacity in gallons and you input 21.1 the decimal doesn’t show-the image is 211.

I’m a Volvo enthusiast, I own three Volvo’s. A 1989 740 GLE; a 1991 940
Non-turbo sedan; a 1998 Volvo V90 wagon.
tbird635
Member
Posts: 15
Post Re: Comprehensive list of PID operators and functions
on: September 19, 2018 (GMT)

Can anyone help ? I’m new to adding PIDs and am just looking to add a simple PID for ethanol fuel sensor hz / percentage.

It’s a flex fuel 1999 Ranger (VIn code V 3.0 ff) with a FF sensor. 1996-2003 Tauruses use the sensor also.

What I haven’t been able to determine yet is if the PID I found is correct for the application.

PID seems to be 16ab . It should output a value between 55 and 115 hertz. ( 55 being straight gasoline 0% , and 115 hz being e85 at 85% .) Newer Flex Fuel Fords do not use the sensor and calculate it a different way.

I tried using torque scan to verify that PID, but it took over an hour and no results.
Also, I can’t get that PID when entered to give me a value.

Am I doing something wrong on the PID scan? Is my PID format correct? (2216ab ) Header necessary?

I don’t necessarily need a value in percentages, just the raw output in hertz.

Thanks for any help you can give me.

rsfjr87
Member
Posts: 18
Post Re: Comprehensive list of PID operators and functions
on: October 6, 2018 (GMT)

And when the pid returns a multi-line response?
How can I select the bytes?

Audis38p
Member
Posts: 2
Post Re: Comprehensive list of PID operators and functions
on: November 8, 2018 (GMT)

Hi i got a 2006 Audi S3 8P i want to read Air /fuel ratio numbers like 1:14.6
How do i get numbers like that? Do i need å Pid?How to instal Pid?

Friendly greetings
Rune Digerud

2006 Audi S3 8P next spring on TTE420 WMI 435-440 BHP Lillestrøm Norway
thesavo
Member
Posts: 1
Post Re: Comprehensive list of PID operators and functions
on: December 5, 2018 (GMT)

Does anyone know if the Ford PIDs for the TPM sensors will work for Jeep? I have a ’14 jeep patriot that I would like to see what the reading look like.

cintakc
Member
Posts: 1663
Post Re: Comprehensive list of PID operators and functions
on: December 5, 2018 (GMT)

Wrangler TPMS 2016.csv

"Name","ShortName","ModeAndPID","Equation","Min Value","Max Value","Units","Header","Diagnostic start command","Diagnostic stop command"
"JEEP Pressure Tyre FL","PresTyre FL","22A020","A*92.46/255","0","92","psi","7DA","1003",""
"JEEP Pressure Tyre FR","PresTyre FR","22A021","A*92.46/255","0","92","psi","7DA","1003",""
"JEEP Pressure Tyre RL","PresTyre RL","22A022","A*92.46/255","0","92","psi","7DA","1003",""
"JEEP Pressure Tyre RR","PresTyre RR","22A023","A*92.46/255","0","92","psi","7DA","1003",""
"JEEP Engine oil pressure","Pres.Oil","22022a","A*147.9/255","0","148","psi","7E0","1092",""
Broken Ford
Member
Posts: 1
Post Re: Comprehensive list of PID operators and functions
on: December 12, 2018 (GMT)

Hello I would like to add ICP VOLTS co a 6.0 Ford diesel.
I use a LG 10 tablet. Oobd 2 and torque pro.
When I change equation A I intently get Variable does not exist.
What do I need to change

oniava
Member
Posts: 36
Post Re: Comprehensive list of PID operators and functions
on: February 3, 2019 (GMT)

Hello.
What formula I need to write to not show negative values?
If (value) is less than 0 then 0 is displayed.
Pages: 1 2 3 4 [5] 6
WP-Forum by: Fredrik Fahlstad, Version: 2.4
Page loaded in: 0.06 seconds.

  Follow me on twitter