Torque

Forums

Forums

Guest  

Show or hide header
Welcome Guest, posting in this forum require registration.

Torque » Torque OBD ECU Scanner » Torque Discussion / Ideas » Sensor refresh rate on version .85

Pages: [1]
Author Topic: Sensor refresh rate on version .85
Hiej
Member
Posts: 173
Post Sensor refresh rate on version .85
on: February 19, 2022 (GMT)

Hi,

on version 1.12.85 ( but also on previous one), the refresh on load and map sensors is slow compared to last versions.

Before the green spot on the load an map dials was so fast to appear solin ON (I have an Obdlink MX that allows 60/80 pids/seconds).
Now the green spot on dials is evidently flashing and movement of needles is not smooth.

Note: for load and map sensors I use 01 mode.

– – – – – – – – – – – – – – – – – – – – – – –
2010 Mazda 2.2d – 185
OBDLink MX – SGS7
– – – – – – – – – – – – – – – – – – – – – – –
piemmm
Administrator
Posts: 6629
Post Re: Sensor refresh rate on version .85
on: February 19, 2022 (GMT)

Hi

The refresh rate is now dynamic – if the values do not change for a few seconds then there’s no point in refreshing the same thing if it’s not changing so the refresh rate is reduced to a lower limit

As soon as the value changes, the refresh rate is back to every single pass

Comments/feedback/critiques on this are welcome
Hiej
Member
Posts: 173
Post Re: Sensor refresh rate on version .85
on: February 21, 2022 (GMT)

Dinamic refresh rate is a good idea, maybe that happens only to me (combination of handset/ecu/obd adapter), but I find that with this metod sensors that requires fast refresh rates are less responsive/sensitive compared to “no dinamic” method.
This is quite noticeable in my case looking at MAP sensor, before it was very sensitive and smooth in changing values now there’s noticeable delay and sometimes there’s a sort of stuttering.

– – – – – – – – – – – – – – – – – – – – – – –
2010 Mazda 2.2d – 185
OBDLink MX – SGS7
– – – – – – – – – – – – – – – – – – – – – – –
piemmm
Administrator
Posts: 6629
Post Re: Sensor refresh rate on version .85
on: February 21, 2022 (GMT)

Ok, I will see if I can improve this for you in the next beta

Edit: Found a part that could be improved, made some small changes and this should be a lot better for your use case now! (1.12.87 beta currently pending approval, should be about an hour) – feedback welcome!
Hiej
Member
Posts: 173
Post Re: Sensor refresh rate on version .85
on: February 22, 2022 (GMT)

Ciao Ian,

yes it seems better now, but dials of engine load and boost (I use a custom pid based on map sensor) are not reactive like before: there’s always a little delay before they start moving if the values are stationary.

– – – – – – – – – – – – – – – – – – – – – – –
2010 Mazda 2.2d – 185
OBDLink MX – SGS7
– – – – – – – – – – – – – – – – – – – – – – –
piemmm
Administrator
Posts: 6629
Post Re: Sensor refresh rate on version .85
on: February 22, 2022 (GMT)

Hi!

Could you email me the pid details (setup/equation/etc) and I’ll see if I can sort that out!

Edit: I’ve also added an option to disable the dynamic refresh in the special settings/options – though I would still like to get hold of the setup/equation/etc that you’re not happy with so I can still improve the dynamic refresh too :)
Pages: [1]
WP-Forum by: Fredrik Fahlstad, Version: 2.4
Page loaded in: 0.025 seconds.

  Follow me on twitter